CCNA 2 R&S Routing and Switching Essentials Chapter 7 Exam

1. Question

2 points

What is the purpose of the passive-interface command?

allows interfaces to share IP addresses
allows an interface to remain up without receiving keepalives
allows a router to send routing updates on an interface but not receive updates via that innterface
allows a routing protocol to forward updates out an interface that is missing its IP address
allows a router to receive routing updates on an interface but not send updates via that interface

2. Question

2 points

What two tasks do dynamic routing protocols perform? (Choose two.)

assign IP addressing
network discovery
propagate host default gateways
update and maintain routing tables
discover hosts

3. Question

2 points

Fill in the blank. Do not abbreviate the answer.

The command (version 2, Version 2, VERSION 2) is used in RIP router configuration mode to enable the sending of subnet masks with the routing updates.

4. Question

2 points

Refer to the exhibit. OSPF is used in the network. Which path will be chosen by OSPF to send data packets from Net A to Net B?

R1, R3, R5, R7
R1, R4, R6, R7
R1, R2, R5, R7
R1, R3, R6, R7
R1, R3, R5, R6, R7

5. Question

2 points

Which two statements are true regarding classless routing protocols? (Choose two.)

is supported by RIP version 1
allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
sends subnet mask information in routing updates
reduces the amount of address space available in an organization
sends complete routing table update to all neighbors

6. Question

2 points

What two actions result from entering the network 192.168.1.0 command in RIP configuration mode on a router? (Choose two.)

The neighboring routers are sent a request for routing updates.
The routing table is created in the RAM of the router.
Routing updates are sent through all the interfaces belonging to 192.168.1.0.
The RIP process is stopped and all existing RIP configurations are erased.
The network address 192.168.1.0 is advertised to the neighbor routers.*

7. Question

2 points

Refer to the exhibit. Based on the partial output from the show ip route command, what two facts can be determined about the RIP routing protocol? (Choose two.)

The command no auto-summary has been used on the RIP neighbor router.
RIP version 1 is running on this router and its RIP neighbor.
RIP will advertise two networks to its neighbor.
The metric to the network 172.16.0.0 is 120.
RIP version 2 is running on this router and its RIP neighbor.

8. Question

4 points

Match the routing protocol to the corresponding category.

Sort elements

RIPv2 (1)
EIGRP (2)
OSPF (3)
IS-IS (4)

distance vector (1)
distance vector (2)
link state (3)
link state (4)

9. Question

2 points

In the context of routing protocols, what is a definition for time to convergence?

the capability to transport data, video, and voice over the same media
the amount of time for the routing tables to achieve a consistent state after a topology change
a measure of protocol configuration complexity
the amount of time a network administrator needs to configure a routing protocol in a small- to medium-sized network

10. Question

2 points

Fill in the blank. Do not abbreviate.

When configuring RIPng, the (default-information originate) command instructs the router to propagate a static default route.

11. Question

2 points

A destination route in the routing table is indicated with a code D. Which kind of route entry is this?

a route dynamically learned through the EIGRP routing protocol
a route used as the default gateway
a network directly connected to a router interface
a static route

12. Question

2 points

Refer to the exhibit. Which interface will be the exit interface to forward a data packet with the destination IP address 172.16.0.66?

Serial0/0/0
Serial0/0/1
GigabitEthernet0/0
GigabitEthernet0/1

13. Question

2 points

Which route is the best match for a packet entering a router with a destination address of 10.16.0.2?

S 10.16.0.0/16 is directly connected, Ethernet 0/1
S 10.16.0.0/24 [1/0] via 192.168.0.9
S 10.0.0.0/8 [1/0] via 192.168.0.2
S 10.0.0.0/16 is directly connected, Ethernet 0/0

14. Question

2 points

Which two requirements are necessary before a router configured with a link-state routing protocol can build and send its link-state packets? (Choose two.)

The router has determined the costs associated with its active links.
The router has constructed an SPF tree.
The router has established its adjacencies.
The routing table has been refreshed.
The router has built its link-state database.

15. Question

2 points

Which two requirements are used to determine if a route can be considered as an ultimate route in a router’s routing table? (Choose two.)

contain a next-hop IP address
contain subnets
be a classful network entry
be a default route
contain an exit interface

16. Question

2 points

What is different between IPv6 routing table entries compared to IPv4 routing table entries?

By design IPv6 is classless so all routes are effectively level 1 ultimate routes.
IPv6 does not use static routes to populate the routing table as used in IPv4.
IPv6 routing tables include local route entries which IPv4 routing tables do not.
The selection of IPv6 routes is based on the shortest matching prefix, unlike IPv4 route selection which is based on the longest matching prefix.

17. Question

2 points

Which dynamic routing protocol was developed as an exterior gateway protocol to interconnect different Internet providers?

RIP
OSPF
EIGRP
BGP

18. Question

2 points

Which route will a router use to forward an IPv4 packet after examining its routing table for the best match with the destination address?

a level 1 child route
a level 1 parent route
a level 2 supernet route
a level 1 ultimate route

19. Question

2 points

Which two statements describe the OSPF routing protocol? (Choose two.)

used primarily as an EGP
has an administrative distance of 100
calculates its metric using bandwidth
automatically summarizes networks at the classful boundaries
uses Dijkstra’s algorithm to build the SPF tree

20. Question

2 points

Which two events will trigger the sending of a link-state packet by a link-state routing protocol? (Choose two.)

the requirement to periodically flood link-state packets to all neighbors
a change in the topology
the initial startup of the routing protocol process
the router update timer expiring
a link to a neighbor router has become congested

21. Question

4 points

Match the characteristic to the corresponding type of routing.

Sort elements

typically used on stub networks (1)
less routing overhead (2)
new networks are added automatically to the routing table (3)
best choice for large networks (4)

static routing (1)
static routing (2)
dynamic routing (3)
dynamic routing (4)

22. Question

6 points

Match the features of link state routing protocols to their advantages and disadvantages.

Sort elements

event-driven updates (1)
building a topological map (2)
fast convergence (3)
bandwidth consumption (4)
memory usage (5)
CPU processing time (6)

Advantage (1)
Advantage (2)
Advantage (3)
Disadvantage (4)
Disadvantage (5)
Disadvantage (6)

Pos.	Name	Entered on	Points	Result
Table is loading
No data available

Modules 1 – 4: Switching Concepts, VLANs, and InterVLAN Routing Exam Answers
Modules 5 – 6: Redundant Networks Exam Answers
Modules 7 – 9: Available and Reliable Networks Exam Answers
Modules 10 – 13: L2 Security and WLANs Exam Answers
Modules 14 – 16: Routing Concepts and Configuration Exam Answers
[Skills Exams] SRWE Practice PT Skills Assessment (PTSA) – Part 1
[Skills Exams] SRWE Practice PT Skills Assessment (PTSA) – Part 2
CCNA 2 v7 Practice Final Exam
CCNA 2 v7 FINAL Exam Answers

Modules 1 – 2: OSPF Concepts and Configuration Exam Answers
Modules 3 – 5: Network Security Exam Answers
Modules 6 – 8: WAN Concepts Exam Answers
Modules 9 – 12: Optimize, Monitor, and Troubleshoot Networks Exam Answers
Modules 13 – 14: Emerging Network Technologies Exam Answers
[Skills Exams] ENSA Practice PT Skills Assessment (PTSA)
ENSAv7 Practice Final Exam
CCNA 3 v7 FINAL Exam Answers

CCNA 2 R&S Routing and Switching Essentials Chapter 7 Exam